Было - ничего не светится, не коннектится, лога нет.
Поменял AR7241, засветились светодиоды (моргают попарно), в логе ожидание TFTP, сети нет.
Процессор и память греются (палец на проце не удержишь)
Снял транзистор RESET
Поменял память, снял зашитные диоды.
Горит один светодиод, загрузка пошла, сети нет.
Процессор греется, но меньше (палец держит).
Что предложит купечество? Поменять трансформатор или еще раз поменять процессор?
Поменял AR7241, засветились светодиоды (моргают попарно), в логе ожидание TFTP, сети нет.
Процессор и память греются (палец на проце не удержишь)
Снял транзистор RESET
Поменял память, снял зашитные диоды.
Горит один светодиод, загрузка пошла, сети нет.
Процессор греется, но меньше (палец держит).
Что предложит купечество? Поменять трансформатор или еще раз поменять процессор?
Спойлер (+/-) (Лог загрузки)
U-Boot 1.1.4.2-s594 (Dec 5 2012 - 15:23:07)
Board: Ubiquiti Networks XM board (rev 1.2 e232)
DRAM: 32 MB
Flash: 8 MB
PCIe WLAN Module found (#1).
Net: eth0, eth1
Hit any key to stop autoboot: 0
## Booting image at 9f050000 ...
Image Name: MIPS Ubiquiti Linux-2.6.32.54
Created: 2013-05-28 14:56:15 UTC
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1047584 Bytes = 1023 kB
Load Address: 80002000
Entry Point: 80002000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Starting kernel ...
Booting...
[ 0.000000] Linux version 2.6.32.54 (buildd@builder) (gcc version 4.1.2) #1 Tue May 28 17:56:11 EEST 2013
[ 0.000000] flash_size passed from bootloader = 0
[ 0.000000] CPU revision is: 00019374 (MIPS 24Kc)
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 02000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone PFN ranges:
[ 0.000000] Normal 0x00000000 -> 0x00002000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x00002000
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
[ 0.000000] Kernel command line: console=ttyS0,115200 root=31:03 rootfstype=squashfs init=/init mtdparts=ar7240-nor0:256k(u-boot),64k(u -boot-env),1024k(kernel),6528k(rootfs),256k(cfg),64k(EEP ROM)
[ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 29388k/32768k available (2289k kernel code, 3380k reserved, 539k data, 136k init, 0k highmem)
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:128
[ 0.000000] plat_time_init: plat time init done
[ 0.000000] Console: colour dummy device 80x25
[ 0.000000] Calibrating delay loop... 259.58 BogoMIPS (lpj=129792)
[ 0.016000] Mount-cache hash table entries: 512
[ 0.019000] NET: Registered protocol family 16
[ 0.021000] ===== ar7240_platform_init: 0
[ 0.021000] PCIe WLAN H/W found [tries: 1]
[ 0.021000] PCI init:ar7240_pcibios_init
[ 0.021000] ar7240_pcibios_init(368): PCI CMD write: 0x356
[ 0.021000] registering PCI controller with io_map_base unset
[ 0.030000] bio: create slab <bio-0> at 0
[ 0.031000] usbcore: registered new interface driver usbfs
[ 0.032000] usbcore: registered new interface driver hub
[ 0.032000] usbcore: registered new device driver usb
[ 0.033000] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[ 0.033000] pci 0000:00:00.0: PME# disabled
[ 0.034000] Returning IRQ 48
[ 0.035000] Switching to clocksource MIPS
[ 0.038000] NET: Registered protocol family 2
[ 0.039000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.040000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
[ 0.040000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.040000] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.040000] TCP reno registered
[ 0.041000] NET: Registered protocol family 1
[ 0.041000] AR7240 GPIOC major 0
[ 0.043000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.043000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.044000] msgmni has been set to 57
[ 0.044000] io scheduler noop registered (default)
[ 0.071000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 0.072000] serial8250.0: ttyS0 at MMIO 0xb8020000 (irq = 19) is a 16550A
[ 0.374000] console [ttyS0] enabled
[ 0.379000] 6 cmdlinepart partitions found on MTD device ar7240-nor0
[ 0.385000] Creating 6 MTD partitions on "ar7240-nor0":
[ 0.390000] 0x000000000000-0x000000040000 : "u-boot"
[ 0.397000] 0x000000040000-0x000000050000 : "u-boot-env"
[ 0.404000] 0x000000050000-0x000000150000 : "kernel"
[ 0.410000] 0x000000150000-0x0000007b0000 : "rootfs"
[ 0.416000] mtd: partition "rootfs" set to be root filesystem
[ 0.422000] 0x0000007b0000-0x0000007f0000 : "cfg"
[ 0.428000] 0x0000007f0000-0x000000800000 : "EEPROM"
[ 0.435000] usbmon: debugfs is not available
[ 0.439000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.476000] Port Status c000004
[ 0.479000] ar7240-ehci ar7240-ehci.0: ATH EHCI
[ 0.484000] ar7240-ehci ar7240-ehci.0: new USB bus registered, assigned bus number 1
[ 0.493000] ehci_reset Intialize USB CONTROLLER in host mode: 3
[ 0.500000] ehci_reset Port Status c000000
[ 0.504000] ar7240-ehci ar7240-ehci.0: irq 3, io mem 0x1b000000
[ 0.511000] ehci_reset Intialize USB CONTROLLER in host mode: 3
[ 0.518000] ehci_reset Port Status c000000
[ 0.528000] ar7240-ehci ar7240-ehci.0: USB 2.0 started, EHCI 1.00
[ 0.534000] usb usb1: configuration #1 chosen from 1 choice
[ 0.540000] hub 1-0:1.0: USB hub found
[ 0.544000] hub 1-0:1.0: 1 port detected
[ 0.549000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 0.556000] u32 classifier
[ 0.559000] Performance counters on
[ 0.562000] input device check on
[ 0.566000] Actions configured
[ 0.572000] TCP westwood registered
[ 0.576000] NET: Registered protocol family 10
[ 0.584000] NET: Registered protocol family 17
[ 0.589000] Bridge firewalling registered
[ 0.593000] 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
[ 0.600000] All bugs added by David S. Miller <davem@redhat.com>
[ 0.606000] ar7240wdt_init: Registering WDT success
[ 0.622000] VFS: Mounted root (squashfs filesystem) readonly on device 31:3.
[ 0.630000] Freeing unused kernel memory: 136k freed
[ 0.648000] Please be patient, while AirOS loads ...
[ 1.803000] Algorithmics/MIPS FPU Emulator v1.5
...mounts done
...filesystem init done
...base ok
...update ok
...symlinks ok
...httpd ok
...detect ok
...caldata ok
...running /sbin/init
Please press Enter to activate this console.
NanoBridge M2 login: ubnt
Password:
May 28 17:55:53 login[924]: root login on 'ttyS0'
BusyBox v1.11.2 (2013-05-28 17:52:06 EEST) built-in shell (ash)
Enter 'help' for a list of built-in commands.
XM.v5.5.6# kist
-sh: kist: not found
XM.v5.5.6# list
-sh: list: not found
XM.v5.5.6# help
Built-in commands:
-------------------
. : [ [[ alias bg break cd chdir command continue echo eval exec
exit export false fg getopts hash help jobs kill let local printf
pwd read readonly return set shift source test times trap true
type ulimit umask unalias unset wait
XM.v5.5.6# ls
cardlist.txt dropbear_dss_host_key dropbear_rsa_host_key
XM.v5.5.6#
Board: Ubiquiti Networks XM board (rev 1.2 e232)
DRAM: 32 MB
Flash: 8 MB
PCIe WLAN Module found (#1).
Net: eth0, eth1
Hit any key to stop autoboot: 0
## Booting image at 9f050000 ...
Image Name: MIPS Ubiquiti Linux-2.6.32.54
Created: 2013-05-28 14:56:15 UTC
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1047584 Bytes = 1023 kB
Load Address: 80002000
Entry Point: 80002000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Starting kernel ...
Booting...
[ 0.000000] Linux version 2.6.32.54 (buildd@builder) (gcc version 4.1.2) #1 Tue May 28 17:56:11 EEST 2013
[ 0.000000] flash_size passed from bootloader = 0
[ 0.000000] CPU revision is: 00019374 (MIPS 24Kc)
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 02000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone PFN ranges:
[ 0.000000] Normal 0x00000000 -> 0x00002000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x00002000
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
[ 0.000000] Kernel command line: console=ttyS0,115200 root=31:03 rootfstype=squashfs init=/init mtdparts=ar7240-nor0:256k(u-boot),64k(u -boot-env),1024k(kernel),6528k(rootfs),256k(cfg),64k(EEP ROM)
[ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 29388k/32768k available (2289k kernel code, 3380k reserved, 539k data, 136k init, 0k highmem)
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:128
[ 0.000000] plat_time_init: plat time init done
[ 0.000000] Console: colour dummy device 80x25
[ 0.000000] Calibrating delay loop... 259.58 BogoMIPS (lpj=129792)
[ 0.016000] Mount-cache hash table entries: 512
[ 0.019000] NET: Registered protocol family 16
[ 0.021000] ===== ar7240_platform_init: 0
[ 0.021000] PCIe WLAN H/W found [tries: 1]
[ 0.021000] PCI init:ar7240_pcibios_init
[ 0.021000] ar7240_pcibios_init(368): PCI CMD write: 0x356
[ 0.021000] registering PCI controller with io_map_base unset
[ 0.030000] bio: create slab <bio-0> at 0
[ 0.031000] usbcore: registered new interface driver usbfs
[ 0.032000] usbcore: registered new interface driver hub
[ 0.032000] usbcore: registered new device driver usb
[ 0.033000] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[ 0.033000] pci 0000:00:00.0: PME# disabled
[ 0.034000] Returning IRQ 48
[ 0.035000] Switching to clocksource MIPS
[ 0.038000] NET: Registered protocol family 2
[ 0.039000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.040000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
[ 0.040000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.040000] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.040000] TCP reno registered
[ 0.041000] NET: Registered protocol family 1
[ 0.041000] AR7240 GPIOC major 0
[ 0.043000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.043000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.044000] msgmni has been set to 57
[ 0.044000] io scheduler noop registered (default)
[ 0.071000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 0.072000] serial8250.0: ttyS0 at MMIO 0xb8020000 (irq = 19) is a 16550A
[ 0.374000] console [ttyS0] enabled
[ 0.379000] 6 cmdlinepart partitions found on MTD device ar7240-nor0
[ 0.385000] Creating 6 MTD partitions on "ar7240-nor0":
[ 0.390000] 0x000000000000-0x000000040000 : "u-boot"
[ 0.397000] 0x000000040000-0x000000050000 : "u-boot-env"
[ 0.404000] 0x000000050000-0x000000150000 : "kernel"
[ 0.410000] 0x000000150000-0x0000007b0000 : "rootfs"
[ 0.416000] mtd: partition "rootfs" set to be root filesystem
[ 0.422000] 0x0000007b0000-0x0000007f0000 : "cfg"
[ 0.428000] 0x0000007f0000-0x000000800000 : "EEPROM"
[ 0.435000] usbmon: debugfs is not available
[ 0.439000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.476000] Port Status c000004
[ 0.479000] ar7240-ehci ar7240-ehci.0: ATH EHCI
[ 0.484000] ar7240-ehci ar7240-ehci.0: new USB bus registered, assigned bus number 1
[ 0.493000] ehci_reset Intialize USB CONTROLLER in host mode: 3
[ 0.500000] ehci_reset Port Status c000000
[ 0.504000] ar7240-ehci ar7240-ehci.0: irq 3, io mem 0x1b000000
[ 0.511000] ehci_reset Intialize USB CONTROLLER in host mode: 3
[ 0.518000] ehci_reset Port Status c000000
[ 0.528000] ar7240-ehci ar7240-ehci.0: USB 2.0 started, EHCI 1.00
[ 0.534000] usb usb1: configuration #1 chosen from 1 choice
[ 0.540000] hub 1-0:1.0: USB hub found
[ 0.544000] hub 1-0:1.0: 1 port detected
[ 0.549000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 0.556000] u32 classifier
[ 0.559000] Performance counters on
[ 0.562000] input device check on
[ 0.566000] Actions configured
[ 0.572000] TCP westwood registered
[ 0.576000] NET: Registered protocol family 10
[ 0.584000] NET: Registered protocol family 17
[ 0.589000] Bridge firewalling registered
[ 0.593000] 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
[ 0.600000] All bugs added by David S. Miller <davem@redhat.com>
[ 0.606000] ar7240wdt_init: Registering WDT success
[ 0.622000] VFS: Mounted root (squashfs filesystem) readonly on device 31:3.
[ 0.630000] Freeing unused kernel memory: 136k freed
[ 0.648000] Please be patient, while AirOS loads ...
[ 1.803000] Algorithmics/MIPS FPU Emulator v1.5
...mounts done
...filesystem init done
...base ok
...update ok
...symlinks ok
...httpd ok
...detect ok
...caldata ok
...running /sbin/init
Please press Enter to activate this console.
NanoBridge M2 login: ubnt
Password:
May 28 17:55:53 login[924]: root login on 'ttyS0'
BusyBox v1.11.2 (2013-05-28 17:52:06 EEST) built-in shell (ash)
Enter 'help' for a list of built-in commands.
XM.v5.5.6# kist
-sh: kist: not found
XM.v5.5.6# list
-sh: list: not found
XM.v5.5.6# help
Built-in commands:
-------------------
. : [ [[ alias bg break cd chdir command continue echo eval exec
exit export false fg getopts hash help jobs kill let local printf
pwd read readonly return set shift source test times trap true
type ulimit umask unalias unset wait
XM.v5.5.6# ls
cardlist.txt dropbear_dss_host_key dropbear_rsa_host_key
XM.v5.5.6#
Комментарий